![[Translate to Englisch (Nordamerika):] [Translate to Englisch (Nordamerika):]](/fileadmin/_processed_/f/1/csm_K_BakitFPK_7kg_E_BE_8f0712ee9f.png)




Bakit FPK
Prefabricated hardwood adhesive
- 1‑component, ready‑to‑use formulation, eliminating the need for on-site mixing and reducing installation time
- Solvent‑, silicone‑ and isocyanate‑free; very low emission (EMICODE EC 1Plus), promoting healthier indoor air quality by significantly reducing airborne pollutants
- Cures to an elastic, moisture‑resistant bond layer
- Easy handling and spreading with standard notched trowels (CS-9, 3/16, or B3 recommended)
- Suitable for radiant‑heated floors
- VOC 0.2 g/l
Bakit FPK is a one-component, polyurethane-free adhesive specifically designed for the elastic installation of engineered wood flooring. It securely bonds engineered hardwood:
- Concrete slabs and cementitious screeds
- Calcium-sulfate (flow) screeds
- Underlayment-grade plywood and OSB
- Substrates prepared with Kiesel patching or leveling compounds
In most cases, no primer is required. Always comply with local building codes and the flooring manufacturer’s installation guidelines.
All substrates must be stable, dry, and clean, free from dust, grease, oil, paint, wax, or any material that could impair adhesion. Surfaces must be structurally sound and free of bond-breaking residues.
- Moisture Testing: Ensure moisture content does not exceed 3 lbs/1,000 ft²/24 h (Calcium Chloride test) or 75% RH (in-situ probe).
- Priming Requirements: Use Okamul® PU-V Schnell (minimum 3-hour cure, must be covered within 48 hours) when installing over mastic-asphalt screeds (IC 10/15) or stable adhesive residues.
- Surface Prep: Mechanically remove any coatings, contaminants, or weak surface layers. Calcium-sulfate screeds must be sanded and primed according to site requirements.
| Details | |
| Trowel | Spread Bakit FPK using a CS-9 3/16 V Notch, or B3 notched trowel held at a 60° angle. |
| Open time | 30–40 minutes (at 20 °C / 68 °F, 65% RH). |
| Flooring installation | No flash time required; embed the flooring within the open time window. |
| Adhesive transfer | Ensure full adhesive coverage beneath the flooring; apply weight if needed until fully cured. |
| Cleanup | Remove fresh adhesive residue immediately with Ki CleanTex wipes |
Color
Beige
Minimum floor temperature
+17 °C / 63 °F
Loadable*
after approx. 48 h
≥ 48 h (3–4 days on non‑absorbent substrates)
Suitable
RS 10 (TRGS 610)
EMICODE®
EC 1Plus (very low emission – GEV)
0,2 g/L
12 months when stored in a climate-controlled environment
*
At 68 °F (+20 °C) and 65% relative humidity. Higher temperature and low humidity decreases, lower temperature and high humidity increases this value respectively.
| Trowel type/notch | Use/Application | Coverage (g/m²) | Coverage per 17 kg (m²) | Coverage per 17 kg (ft²) | Typical coverage per US gallon (ft²) | Coverage per 2.64 gal (ft²) |
| CS-9 ³⁄₁₆" V Notch | Engineered wood | 1,072 | 16 | 172 | 65 | 172 |
| German TKB B3 approx.: ⅛" × ⅛" × ⅛" |
Kiesel non-woven underlay, sound insulation underlay | 800–850 | 20–21 | 215–229 | 81–87 | 215–229 |
| German TKB B7 approx.: ¹⁵⁄₆₄" × ¹⁵⁄₆₄" × ¹⁵⁄₆₄" | Engineered wood, short boards (DIN EN 13489) | 850–1,050 | 16–20 | 172–215 | 66 - 81 | 172–215 |
| German TKB B11 approx.: ³⁄₁₆" × ⁵⁄₁₆" × ¹⁵⁄₆₄" | Boak engineering, board format (DIN EN 13489) | 1,050–1,200 | 14–16 | 151–172 | 58 - 66 | 151–172 |
German TKB B15 approx.: ¹¹⁄₃₂" × ¹¹⁄₃₂" × ¹¹⁄₃₂"
| OkaQuiet | 1,200–1,500 | 11–14 | 118–151 | 46–58 | 118–151 |
Coverage may vary based on substrate texture, porosity, and application technique.
Clean tools immediately after use with Ki CleanTex wipes. Cured adhesive can only be removed mechanically.
| Description | Item No. | |
|---|---|---|
| 17 kg/ 4.22 U.S. gal/ 15.99 Liters plastic bucket | 46051 | 4015705460512 |
The aforementioned information, especially the proposals for processing and utilizing our product, is based on our knowledge and experience. We recommend that you carry out your own tests in every case to ensure the suitability of our products for the intended process and processing purposes because of the different materials and the working conditions which lie beyond our area of influence. No liability can be derived from this advice or from verbal advice, unless we are responsible for (criminal) intent or gross negligence in this respect.