Okatmos® star 100 Plus

Wet and pressure sensitive adhesive

Short ventilation time
Solvent free and very low emission
Universally applicable
Easy trowelable
Anti-microbial technology
Breathe easy technology

Solvent-free (according to TRGS 610), very low-emission wet bed and pressure-sensitive adhesive for bonding, LVT, homogeneous and heterogeneous PVC flooring in strips and tile format, VCT floor coverings, rubber up to 4.0 mm thick in sheeting and tile format, linoleum up to 3.2 mm thickness as well as textile floor coverings. Okatmos® star 100 Plus can be used as wet bed and pressure sensitive adhesive as well as in the contact method (double-drop). Okatmos® star 100 Plus contributes to the prevention of odors with its antimicrobial properties.

The substrate must comply with VOB Part C, DIN 18 365, current data sheet BEB as well as with all technical requirements and must be ready for installation. The surface must be sound and clean. Remove dirt, paint, oil, grease wax and other contamination which might act as a bond breaker. Prepare all non-absorbent substrates with Kiesel suitable primers and level using Kiesel self leveling compounds. Before installing vapor-tight coverings prepare substrate with self leveling compound.

Okatmos® star 100 Plus should be used as a product component together with other Kiesel floor installation system products.

Mix Okatmos® star 100 Plus well if necessary. Use appropriate notched trowel to apply the adhesive onto the substrate. Install covering after a drying time of 5 - 40 minutes and roll down. Ensure a full area application on the back of the covering. Technical Data Sheet approx. 30 - 60 minutes. Please follow the installation instructions of the flooring manufacturer, especially the directions for covering acclimation. Weld joints no earlier than two days after the installation.

	Absorbent and leveled substrates	Dense, non-absorbent substrates
	Wet-bed Half-wet bed	Pressure sensitive	Contact method (double-drop method)
Coverings	PVC floor coverings, CV and LVT coverings, Vinyl floor coverings, Rubber sheet linoleum, Textile floor coverings	LVT, PVC coverings, CV coverings, Wall coverings,	PVC coverings, CV coverings, Wall coverings
Trowel size	TKB A2 TKB B1	TKB A5	TKB A5
Open time	5 - 30 minutes	30 - 40 minutes	10 - 15 minutes reapply the covering 20 - 25 minutes cover again
Insertion time	20 - 40 minutes	50 - 120 minutes	35 - 40 minutes

Color

Cream white

VOC

0,0 g/L

Antimicrobial technology

Yes

Recycle content

n/a

Application

Interior

Tensile strength

Suitable

Minimum floor temperature

59 °F/ +15 °C

Skin over time*

Approx. 5 - 40 minutes

Open time (working)

Approx. 40 minutes (covering dependable)

Ready for installation*

After approx. 24 hours

Final strength*

After approx. 72 hours

Floor heating system

Suitable

GISCODE

D 1 according to TRGS 610

EMICODE

EC 1^Plus

Storage

Store in frost protected area for up to 12 months

At 68 °F (+20 °C) and 65 % relative humidity. Higher temperature and low humidity decreases, lower temperature and high humidity increases this value respectively.

The floor coverings must be sufficiently relaxed, acclimatized, and adapted to the room climate for future use. The relevant information and instructions given by the manufacturer of the floor covering must be observed.

Heavy rolling tension, protruding edges or padding, creases are to be weighed during the installation until the adhesive has set.
In case of high temperature loads, e.g. By sun direct exposure in winter gardens or on window sills, when subjected to heavy mechanical loads by lifting trucks, floor conveyor vehicles or the like. As well as surface moisture condensation, it is preferable to use Okamul PU or to obtain additional application advice.
In the case of floor covering, the generally accepted rules of the subject and the technique, as well as the current standards and information sheets, must be taken into account. In particular:
- DIN 18365 "Flooring work"
- BEB-guideline "Assessment and preparation of substrates"
- TKB-guideline "Assessment and preparation of subfloors for flooring and parquet work"
- TKB-guideline "Bonding of Elastomer Flooring"
- TKB-guideline "Bonding of PVC floor coverings"
- TKB guideline "Bonding of linoleum floor coverings"
- TKB-guideline "Bonding of textile floor coverings"

Covering type	Trowel size	Coverage
CV and LVT covering	TKB A5 TKB A2	250 - 300 g/m² 200 - 250 g/m²
PVC covering, Vinyl covering, Rubber covering	TKB A2	250 - 300 g/m²
Linoleum textile coverings	TKB B1	300 - 350 g/m²
CV and LVT covering	¹/₁₆“ x ¹/₁₆“ x ¹/₁₆“ ¹/₁₆“ x ¹/₁₆“ x ³/₃₂“	163 - 194 ft². per U.S. gals. 194 - 244 ft². per U.S. gals.
PVC covering, Vinyl covering, Rubber covering	¹/₁₆“ x ¹/₁₆“ x ³/₃₂“	163 - 194 ft². per U.S. gals.
Linoleum textile coverings	¹/₁₆“ x ¹/₁₆“ x ³/₃₂“ + ¹/₃₂“ x ¹/₁₆“ x ¹/₃₂“	142 - 163 ft². per U.S. gals.

Coverage is estimated by trial-application on Servoplan Ki 1. It may vary on different substrates and depends on application angle and manufacturer of trowel.

Clean tools with water immediately after application.

Description	Item No.
33 x 3.04 U.S. gals./ 14 kg plastic buckets

The aforementioned information, especially the proposals for processing and utilizing our product, is based on our knowledge and experience. We recommend that you carry out your own tests in every case to ensure the suitability of our products for the intended process and processing purposes because of the different materials and the working conditions which lie beyond our area of influence. No liability can be derived from this advice or from verbal advice, unless we are responsible for (criminal) intent or gross negligence in this respect.