Oka Silicon „NEW“

Silicon caulk

  • Colors match Servofix and Servoperl grouts
  • Extreme stress resistance
  • Anti-fungal properties
  • Non-aging
  • Suitable for interior and exterior use
  • UV resistant

Oka Silicon is a high quality, self curing, high-stress, one component silicon sealing compound. The permanently elastic joint sealer is suitable for sanitary areas around bathtubs and sinks, and to caulk expansion joints in ceramic coverings.

Oka Silicon provides a short-term resistance to alkaline/causticacids and lye‘s, industrial emissionsand corresponds to DIN 18 545 E. The sealer should not be used over alkaline substrates (such as concrete, etc.), non-ferrous metals or for assembling fish tanks.

If used on agglomerated and natural stone coverings, penetration and edge coloration may occur. Oka Silicon cannot be coated. For natural stone application use Oka M Silicon.

Please contact the Kiesel Technical Service Department for information on using Oka Silicon in submergedareas.

Check existing substrate for suitability. The surface must be clean, dry, load bearing and free of dust and grease. Clean substrates such as glass, aluminum, iron with rust proof paint, enamel and ceramics with a special cleaning solution before application. Prime glazed wood and hard/soft PVC before application. For more detailed information see the Kiesel primer table.

Because of its coloration characteristics, Oka Silicon should not be used in contact with bituminous materials.

Cover joint edges with masking tape. Cut tip of tube, attach application nozzle and shape to joint width. Insert tube into manual or pneumatic caulking gun and fill joints evenly. Smoothen with small amounts of a suitable smoothing compound with a knife or finger immediately after application. Remove any excess smoothing compound as well as masking tape immediately after application.

Color

Transparent, white, grey, black and all colors matching Servofix, Servoflex and Servoperl colors (see respective color charts)

Application

Interior, exterior, walls and floors

Density

Approx. 1,03 g/cm³

Shore-A-Hardness

Approx. 18 ± 5 (DIN 53505)

Tensile strength

2,6 N/mm² (DIN 53504)

Elongation at break

800 % (DIN 53504)

Permanent expansion capacity

25 %

Resilience

> 90 % (ISO 7389-B)

Temperature tolerance

-10 °C to +40 °C (min. substrate temp. +5 °C)
50 °F to 104 °F (min. substrate temp. 41°F)

Elastic modulus

(100%) 0,3 N/mm² (DIN EN ISO 8339)

Application temperature

-10 °C to +40 °C (Underground +5 °C)

Cure time*

Approx. 2 mm/day

Building material group

B2 (DIN 4102 part 4) (normal flammability)

Storage

store in a cool and dry area for up to 18 months**

At 68 °F (+20 °C) and 65 % relative humidity. Higher temperatures and lower humidity decreases, lower temperatures and high humidity increase this value respectively.

1 tube will cover approximately 12 current meters at 5 x 5 mm joint cross section.

Clean tools with acetone immediately after application.

Description Item No. EAN
kaffee60292
transparent60126
white60015
grey60016
jasmine60023
light brown60025
black velvet60018
basalt60313
brasil60031
topaz60039
edelweiß60040
manhattan60041
sahara60043
pergamon60106
light grey60017
middle grey60105
silver grey60210
sand grey60314
shadow60324
safari sand60325
mochacino60326
desert sand60327
anthracite60335
red60046
blue60047
green60048
creamy yellow60236
primer 15060208
snow60354
camel60355
bahama60356
universal grey60357
cocoa60358
fog60359
black velvet60018
90 boxes per 12 x 310 ml tubes per box

The aforementioned information, especially the proposals for processing and utilizing our product, is based on our knowledge and experience. We recommend that you carry out your own tests in every case to ensure the suitability of our products for the intended process and processing purposes because of the different materials and the working conditions which lie beyond our area of influence. No liability can be derived from this advice or from verbal advice, unless we are responsible for (criminal) intent or gross negligence in this respect.